33220A MANUAL PDF

It covers both front panel and remote interface operation. Pulse Width Modulation PWM PWM is used in digital audio applications, motor z circuitry, switching power supplies, and other control applications. This command is similar to a Serial Poll but it is processed like any other instrument command. To set the output frequency, press the Freq softkey for the selected function. Index gated burstdefault address 48 invert waveform 67 gated burst mode front-panel configuration 48 IP address 50, gateway address service request dot notation 52 gaussian noise setting address 48 further information 52 GPIB immediate trigger, address 48, Chapter 5 Error Messages Execution Errors Settings conflict; FM deviation cannot exceed carrier The a frequency must always be greater than or equal to the frequency deviation. In some cases, the amplitude limits are determined by the output units selected.

Author:Bami Gardam
Country:Seychelles
Language:English (Spanish)
Genre:Education
Published (Last):20 May 2005
Pages:337
PDF File Size:12.28 Mb
ePub File Size:16.83 Mb
ISBN:403-1-37694-235-1
Downloads:11166
Price:Free* [*Free Regsitration Required]
Uploader:Arashilar



Its combination of bench-top and system features makes this function generator a versatile solution for your testing requirements now and in the future. The variation in frequency of the modulated waveform from the carrier frequency is called the frequency deviation. To set the waveform period instead, press the Freq softkey again to toggle to the Period softkey.

Select linear or logarithmic spacing for the sweep. However, you cannot overwrite any of the five built-in waveforms. Chapter 3 Features and Functions Calibration Overview Calibration Message The function generator allows you to store one message in calibration memory in the mainframe.

A query of this register returns a decimal value which corresponds to the binary- weighted sum of all bits set in the register. This information is not directly related to waveform generation but is an important part of operating the function generator.

Refer to the Agilent A Service Guide for more information on the calibration procedures. For periods above 10 seconds, the minimum pulse width is greater.

SOUR command to select the source from which the sweep will be triggered. Chapter 5 Error Messages Execution Errors Settings conflict; FSK turned off by selection of other mode or modulation The function generator will allow only one modulation, sweep, or burst mode to be enabled at the same time. PM is very similar to FM, but in PM the phase of the modulated waveform is varied by the instantaneous voltage of the modulating waveform.

The isolation between chassis ground circuits and floating circuits is controlled by an optical isolation barrier and a serial link. With autoranging disabled, the function generator uses the current amplifier and attenuator settings. Page Chapter 3 Features and Functions Triggering External Triggering In the external trigger mode, the function generator will accept a hardware trigger applied to the rear-panel Trig In connector.

Chapter 3 Features and Functions Pulse Width Modulation PWM Width Deviation The width deviation represents the variation in width in seconds in the modulated waveform from the width of the original pulse waveform. Chapter 7 Tutorial Modulation Modulation Modulation is the process of modifying a high-frequency signal called the carrier signal with low-frequency information called the modulating signal. To set the output frequency, press the Freq softkey for the selected function.

Front-Panel Number Entry You can enter numbers from the front-panel using one of two methods. In AM amplitude modulationthe amplitude of the carrier is varied by the amplitude of the modulating waveform. This chapter describes basic signal-generation concepts and gives specific details on the internal operations of the function generator.

Then use the knob or numeric keypad to enter the desired frequency. For arbitrary waveforms, the maximum offset and amplitude will be limited if the waveform data points do not span the full range of the output DAC Digital-to-Analog Converter.

MIN selects the most negative dc offset voltage for the selected function and amplitude. The rise time and fall time cannot be a independently—each is equal to the edge time. In FM, the frequency a the carrier is varied by the instantaneous voltage of the modulating waveform. The default is NORM true-high logic. Chapter 5 Error Messages Error Messages In fact, any periodic signal can be represented as the sum of different sine waves. You can create an arbitrary waveform from the front panel as described in the following section, or you can use the Agilent IntuiLink software provided on the CD-ROM included with the Agilent A.

To configure the function generator to recall the factory default state at manal, press and then select the Pwr-On Default softkey. Got it, continue to print. Chapter 7 Tutorial Tutorial Make sure you have read the security code rules described on page before attempting to change the security code.

APC BH500NET PDF

33220A MANUAL PDF

Its combination of bench-top and system features makes this function generator a versatile solution for your testing requirements now and in the future. The variation in frequency of the modulated waveform from the carrier frequency is called the frequency deviation. To set the waveform period instead, press the Freq softkey again to toggle to the Period softkey. Select linear or logarithmic spacing for the sweep. However, you cannot overwrite any of the five built-in waveforms. Chapter 3 Features and Functions Calibration Overview Calibration Message The function generator allows you to store one message in calibration memory in the mainframe.

BOB CASSIDY THE ART OF MENTALISM PDF

AGILENT 33220A DRIVERS FOR WINDOWS

Comments and Ratings 4. Select agilent a China site in Chinese or English for best site performance. Jim Grayson 6 Nov Redistribution and use in source and binary agilent a, with or without modification, are permitted agilent a that the following conditions are met: Agilent Afilent Function Generator — Driver version 1. Requires Instrument Control Toolbox. Other MathWorks country sites are not optimized for visits from your location. Copyright cThe MathWorks All rights reserved.

ADOLESCENCE IAN MCMAHAN PDF

Download manual

Chapter 5 Error Messages Execution Errors Settings conflict; FSK turned off by selection of other mode or modulation The function generator will allow only one modulation, sweep, or burst mode to be enabled at the same time. This error is also reported when a character-type parameter is too long. The variation in phase of the modulated waveform from the carrier waveform is called the phase deviation, which can vary from 0 to degrees. You can output the burst at a rate determined by the internal rate generator or the signal level on the rear-panel Trig In connector. The default is Internal.

ECONOMETRIA WOOLDRIDGE ESPAOL PDF

AGILENT 33220A MANUAL PDF

.

Related Articles